Search results
Create the page "Plywood" on this wiki! See also the search results found.
Page title matches
Page text matches
- [[Category:Molded Plywood]]991 bytes (134 words) - 14:49, 25 May 2021
- ...pper Craft of Maryland]], an East-Coast outboard boat-builder using molded plywood hulls. ...ded by a former [[Chris Craft]] employee who built sheet plyood and molded plywood boats in Holland, Michigan.779 bytes (103 words) - 16:38, 16 December 2020
- [[Category:Molded Plywood]]461 bytes (64 words) - 23:10, 16 July 2014
- ...les Times). Plywood boats used US Plywood Corporation's [[Weldwood]] brand plywood (January 31, 1958 Los Angeles Times). [[Category:Sheet Plywood]]2 KB (328 words) - 12:50, 11 May 2021
- [[Category:Sheet Plywood]]603 bytes (80 words) - 16:21, 14 November 2015
- ...rticle below, this company made a 35' steel houseboat with marine mahogany plywood cabin.700 bytes (91 words) - 01:19, 11 November 2015
- ...o 20' in length. The boats had two-tone mahogany decks, fiberglass-covered plywood bottoms. More information is needed, so please send us anything you may hav [[Category:Plywood]]710 bytes (106 words) - 15:57, 24 May 2015
- In 1958, this company offered a single model of 26' plywood-hull, flat-bottom houseboat, for inboard or outboard power.558 bytes (68 words) - 18:27, 8 April 2021
- [[Category:Sheet Plywood]]883 bytes (121 words) - 17:18, 7 September 2015
- [[Category:Sheet Plywood]] [[Category:Molded Plywood]]792 bytes (105 words) - 17:36, 7 September 2015
- This company seems to have offered a range of models based on molded plywood hulls. [[Category:Molded Plywood]]627 bytes (88 words) - 17:37, 7 September 2015
- This company offered a plywood pontoon boat in 12' and 16' lengths.396 bytes (56 words) - 01:15, 23 September 2015
- [[Category:Sheet Plywood]]876 bytes (103 words) - 15:22, 16 April 2021
- Chris Craft's Cavalier line of boats were made with sheet-plywood hulls and therefore were a more inexpensive alternative to the main Chris-C [[Category:Sheet Plywood]]2 KB (243 words) - 20:53, 19 November 2020
- ...hris Craft Cavalier]] division success in marketing higher value, finished plywood boats relegated the Kit Boat division to a cost-cutting competitor for cons1 KB (202 words) - 13:34, 7 April 2021
- ...rate of 2 boats per day were planned. Construction was of mahogany and fir plywood with white oak frames. A special water ski compartment was included in the [[Category:Plywood]]1 KB (183 words) - 16:46, 26 September 2015
- ...leadership of company owner John Ek. These were fiberglass-covered marine plywood boats and were offered complete and in kit form.648 bytes (91 words) - 01:05, 9 October 2015
- ...at (see articles below). The Flying Dutchman was made on a molded mahogany plywood hull. The Blue Jay was designed by Sparkman & Stephens. The Blue Jay and In [[Category:Molded Plywood]]1 KB (147 words) - 01:22, 9 October 2015
- ...atten-seam construction with both inboard and outboard models. Later, some plywood models were offered. In 1957, the company had a 15,000 square foot plant an | Fisherman||OB||||13'5"||54"||40||||4||225||Mahogany Plywood2 KB (244 words) - 17:17, 25 January 2019
- ...win-hull outboard-powered catamarans made out of fiberglass-covered marine plywood. At least three different models were made ranging from 13'9" to 18'. These [[Category:Sheet Plywood]]1 KB (151 words) - 03:34, 3 November 2016